Tungsten carbide burrs for high performance, ALLROUND HC-FEP, conical shape with radius end KEL

Tungsten carbide high-performance burr ALLROUND tree shape with radius end KEL dia. 10x20mm shank dia. 6mm HICOAT universal

Item number:: 21001053
EAN:: 4007220222010

Tungsten carbide high-performance burr ALLROUND tree shape with radius end KEL dia. 10x20mm shank dia. 6mm HICOAT universal 2

Technical data Change variant

Choose options

Dia. external

10 mm 12 mm

Dia. shank

6 mm

Length, cut

20 mm 25 mm

Length, total

60 mm 70 mm

Reset Filter

Technical information

Tungsten carbide high-performance burr ALLROUND tree shape with radius end KEL dia. 10x20mm shank dia. 6mm HICOAT universal

Angle: 14 °
Cut: ALLROUND HC-FEP
Dia. external: 10 mm
Dia. shank: 6 mm
Length, cut: 20 mm
Length, total: 2,362
Length, total: 60 mm
RPM from, hard non-ferrous metals: 14000 RPM
RPM from, hardened, heat-treated steels over 1,200 N/mm²: 8000 RPM
RPM from, rust and acid-resistant steels: 14000 RPM
RPM from, soft non-ferrous metals: 14000 RPM
RPM from, steels up to 1,200 N/mm²: 14000 RPM
RPM to, hard non-ferrous metals: 24000 RPM
RPM to, hardened, heat-treated steels over 1,200 N/mm²: 19000 RPM
RPM to, rust and acid-resistant steels: 19000 RPM
RPM to, soft non-ferrous metals: 29000 RPM
RPM to, steels up to 1,200 N/mm²: 29000 RPM
Radius corner design: 2.9 mm
Packaging unit: 1 piece

Description

High-performance cut ALLROUND with HICOAT coating HC-FEP is characterized by its high degree of hardness and wear resistance. It enables effective chip removal through improved anti-adhesion characteristics and is highly temperature-resistant. It allows for a longer tool life and use at higher cutting speeds in comparison with uncoated burrs.

Conical burr with round radius end according to DIN 8032.

Advantages

Significantly better stock removal rate than burrs with a conventional cross cut.
Saves time and money thanks to its very high stock removal rate on key materials.
Comfortable working with reduced vibration and less noise.
The highly accurate concentricity enables impactfree working without creating chatter marks. This considerably reduces wear on the tool and tool drive.

Recommendations for use

To prevent vibrations, place the tools on powerful drives with an elastically supported spindle wherever possible.
Observe the recommended rotational speeds.
If the smallest area of the burr diameter is being used, the recommended rotational speed can be increased accordingly.
To ensure costeffective use of burrs, use a higher rotational speed and cutting speed. Use burrs with a shank diameter of 6 mm with drives with a power output from 300 watts.

Safety notes

The very high stock removal rate can cause discolouration on the shank. This does not constitute a safety risk.

Materials that can be worked: Case-hardened steels; Cast steel; Hard aluminium alloys; Hardened, heat-treated steels over 1.200 N/mm² (< 38 HRC); Steel; Steel, cast steel; Steels over 700 N/mm² (> 220 HB); Steels up to 1,200 N/mm² (< 38 HRC); Steels up to 700 N/mm² (< 220 HB); Tool steels

Applications: Cutting out holes; Deburring; Leveling; Milling; Milling out; Surface work; Work on weld seams

Drive types: Drive spindle; Flexible shaft drive; Robot; Stationary machines; Straight grinder; Tool machine

PFERDVALUE

PFERDEFFICIENCY

recommends burrs with the HICOAT coating for working for long periods with low levels of fatigue, whilst saving resources and achieving perfect results as quickly as possible.